型号

包装规格

每箱数量

产品代号

PRODUCT DESCRIPTION

PERMATEX The Right Stuff for Imports is a singel component,

room temperature curing, elastomeric gasketing compound

designed to provide reliable "formed-in-place" gaskets for

mechanical assemblies. The Right Stuff for Imports has been

specifically designed to perform under higher torque loads

of engines with high bolt densities, typically import vehicles.

This product has a high blowout resistance, allowing leakpr

oof gaskets to be made and placed into service immediately

after reassembly. Permatex Right Stuff for Imports is sensor

safe and seals instantly forming reliable, long lasting elastom

eric rubber gaskets that outperform precut gaskets. OEM spe

cified by Nissan, Honda Mazda and Kia

PRODUCT BENEFITS

● Immediate sealability

● Instant blow-out resistance

● Import OEM Approved and Specified

● Replaces most cut gaskets

● Low odor

● Resistant to ATF/oil/coolant

● Consistent sealing

● Sensor safe

TYPICAL APPLICATIONS

● Timing gear covers

● Transmission pans

● Valve covers

● Oil pans

● Water pumps

● Gearboxes

● Intake manifold end seals

● Stamped sheet metal covers

● Compressors

● Gearboxes

PROPERTIES OF UNCURED MATERIAL

                                                             Typical Value

Chemical Type                                Elastomeric Rubber

Appearance                                         Metallic Grey

Specific Gravity @20℃                              1.45

Viscosity                                            Thixotropic Paste

Flash Point(TCC),_F                                     >200

DIRECTIONS FOR USE

For assembly as form-in-place gasket

1.Remove all previous material from mating surfaces.Permatex

   Gasket Remover is recommended for most materials(not for

   plastics or painted surfaces).

2.For best results, clean and dry all surfaces with a residue-free

   solvent, such as Permatex Brake and Parts Cleaner.

3.Cut nozzle to desired bead size, 1/16 to 1/4 in

   diameter. An 1/8 bead is usually sufficient for most

    applications.

4.Remove cap, puncture tube or cartridge seal and attach

   extension nozzle.

5.Apply a continuous and even bead of The Right Stuff

   for Imports to one surface, first tracing the internal areas

   of the gasket configuration, then all surrounding bolt

    holes as shown below.

6.Assemble parts within 5 minutes while The Right Stuff

   for Imports is still wet. Secure or tighten to recommend

    ed torque specs

7.Re-torque will not be necessary after the product has

   cured.

For Cleanup

1.Allow excess material to extend beyond the extension

   nozzle or aerosol tip to cure, sealing and protecting the

   remaining product from moisture. For reuse, simply

   remove the cured product from the tip.

2.Remove uncured product from parts and hand-tools with

   a dry cloth, if skinned over, break film with a dry cloth to

   remove as much as possible, and remove the remaining

   material with Permatex Gasket Remover as previously

   stated.

3.Clean hands with a dry cloth or Permatex Fast Orange

   hand cleaner.

TYPICAL CURING PERFORMANCE

Cure Time

The surface of this adhesive becomes dry to touch on

exposure to atmospheric moisture within 5 minutes at 23

-2 ℃，50-5%RH,The product cures on exposure to moisture

in the air and dries tack free in two hours, with full cure in

24 hours. Cure times will vary with temperature, humidity

and gap.

Instant Seal

Parts assembled with Permatex The Right Stuff for Imports

are instantly sealed and can be immediately placed into service

TYPICAL PROPERTIES OF CURED MATERIAL

                                                                   Typical Value

Hardness,Shore A,ASTM D2240                           60

Elongation at break,%,ASTM D412                       175

Tensile strength ,N/MM²,ASTM D412                  3.4min