型号

包装规格

每箱数量

产品代号

PRODUCT DESCRIPTION

Permatex Clear Silicone Adhesive Sealant is a general pur

pose, single component, room temperature vulcanizing (

RTV) adhesive/sealant compound, designed for the sealing

of mechanical assemblies. Upon curing from the exposure

to moisture in the air, this non-sagging paste forms a tough,

flexible, waterproof seal of silicone rubber, which resists a

ging, weathering and thermal cycling without hardening,

shrinking or cracking. Conforms to MIL-A-46106B, Type I, 

Permatex Clear RTV Silicone Adhesive Sealant shall meet

the requirements of the F.D.A. "Code of Federal Regulations

21 CFR" concerning food contact applications if use in acc

ordance with its Section 177.2600:"Rubber Articles Inten

ded for Repeated Use".

PRODUCT BENEFITS

● Easy application

● Applied to horizontal or vertical surfaces

● Superior adhesion and flexibility

● Waterproofs

● Insulates

● Unaffected by vibration

● Non-flammable

● Non-toxic

TYPICAL APPLICATIONS

Permatex Clear Silicone Adhesive Sealant is an excellent all

-purpose adhesive/sealant for the following materials：

● Metal

● Glass

● Wood

● Plastic

● Vulcanized silicone rubber

● Ceramics

● Natural and synthetic fibers

● Painted surfaces

DIRECTIONS FOR USE

For Assembly

1.Remove all previous material from mating surfaces. Perm

   atex Gasket Remover is recommended for most materials,

   not for plastics or painted surfaces.

2.For best results, clean and dry all surfaces with a residue-

   free solvent, such as Permatex Brake and Parts Cleaner.

3.Cut nozzle to desired bead size, 1/16 to 1/4 in diameter.

   A 1/8 bead is usually sufficient for most applications.

4.Remove cap, puncture tube or cartridge seal and attach

  extension nozzle.

5.Apply a continuous and even bead of silicone to one 

   surface.

6.Assemble parts immediately while silicone is still wet.

  Secure or tighten as required, avoiding excessive

    squeeze-out.

7.Pressure should be applied to parts for 24 hours until

   the silicone is fully cured.

Instructions for PowerBead

1.Clean and dry all flange surfaces to be sealed.

2.Remove black cap from top of extension nozzle.

3.Turn nozzle extension one complete turn(360)

   counterclockwise

4.Depress finger trigger and apply a continuous 1/16 inch

   to 1/8 inch PowerBead to one surface

5.Apply a continuous and even bead of silicone to one

   surface.

6.Assemble parts immediately while silicone is still wet.

   Secure or tighten as required, avoiding excessive squ

   eeze-out.

7.Pressure should be applied to parts for 24 hours until the

   silicone is fully cured.

8.To close, turn extension nozzle clockwise until tight ( about

  one full turn). Wipe off excess material from nozzle and

   replace black cap.

Stotage of Unused Product

1.Create a "Silicone Plug" by allowing excess material to ex

   tend beyond the extension nozzle or aerosol tip to cure,

    sealing and protecting the remaining product from moisture.

     For reuse, simply remove the cured product from the tip.

2.For PowerBead dispensers, you may store remaining product

   using either the above"silicone plug" method or using the

    included plastic cap.

For Cleanup

1.Remove uncured product from parts and hand-tools with

    Permatex Envirosafe ODC Free Cleaner/Degreaser. If skin

     ned over, break film with a dry cloth to remove as much

      as possible. Remove the remaining material with Permatex

      Gasket Remover.

2.Clean hands with a dry cloth or Permatex Fast Orange hand

     cleaner.

PROPERTIES OF UNCURED MATERIAL

                                                              Typical Value

Chemical Type                                  Acetoxy silicone rubber

Appearance                                       Clear, non-sag paste

Odor                                                       Mild acetic

Specific Gravity                                            1.01

Extrusion rate@25℃，(grams/min)             >220

Flash Point _℃，_℉                                  >93(>200)