型号

包装规格

每箱数量

产品代号

PRODUCT DESCRIPTION

PERMATEX® The Right Stuff is a single component, room

temperature curing, elastomeric gasketing compound desi

gned to provide reliable “formed-in-place” gaskets for mech

anical assemblies. The Right Stuff is a non-slumping,non-

corrosive, low odor, low volatile, single component, proprie

tary, hi-tech, elastomeric rubber gasketing material. It has b

een designed specifically as a replacement for conventional

 cut gaskets where instant sealability is advantageous. The 

product resists aging, weathering and thermal cycling witho

ut hardening, shrinking or cracking. Designed for superior b

onding properties to oil contaminated metals as compared t

o other formed-in-place gaskets, and maintains outstanding 

oil resistance. NSF White Book registered.

PRODUCT BENEFITS

• Immediate sealability

• Instant blow-out resistance

• OEM Approved and Specified

• Replaces most cut gaskets

• Low odor

• Resistant to ATF/oil/coolant

• Consistent sealing

• Sensor safe

TYPICAL APPLICATIONS

• Timing gear covers

• Transmission pans

• Valve covers

• Oil pans

• Water pumps

• Gearboxes

• Intake manifold end seals

• Stamped sheet metal covers

• Compressors

• Gearboxes

DIRECTIONS FOR USE

For assembly as a form-in-place gasket

1. Remove all previous material from mating surfaces.

Permatex Silicone Stripper is recommended for most

materials.

2. For best results, clean and dry all surfaces with a residue-

    free solvent, such as Permatex Brake and Parts 

    Cleaner.

3. Cut nozzle to desired bead size, 1/16“ to 1/4“ in diameter. 

     An 1/8” bead is usually sufficient for most applications.

4. Remove cap, puncture tube or cartridge seal and

attach extension nozzle.

5. Apply a continuous and even bead of The Right Stuff

to one surface, first tracing the internal areas of the

gasket configuration, then all surrounding bolt holes as

shown below:

6. Assemble parts within 5 minutes while The Right Stuffis still 

     wet. Secure or tighten to recommended torque specs.

7. Re-torque will not be necessary after the product has

 cured.

Note: Not for use as a head gasket or on parts in contact

 with gasoline

Directions for PowerBead

1. Clean and dry all flange surfaces to be sealed.

2. Remove black cap from top of extension nozzle.

3. Turn nozzle extension one complete turn (360°)

   counterclockwise.

4. Depress finger trigger and apply a continuous 1/

  16 inch to 1/8 inch PowerBead to one surface.

5. Assemble parts within 5 minutes while The Right

   Stuff is still wet. Secure or tighten to recommended

    to rquespecs.

6. Parts or vehicle may be placed back into service immediately.

7. Re-torque will not be necessary after the product has

    cured.

8. To close, turn extension nozzle clockwise until tight

    (about one full turn). Wipe off excess material from

     nozzle and replace black cap.

Storage of Unused Product

1. Create a “silicone plug” by allowing excess material to

extend beyond the extension nozzle or aerosol tip to cure, sea

ling and protecting the remaining product from moisture. 

For reuse, simply remove the cured product from the tip.

2. For PowerBead dispensers, you may store remaining product 

using either the above “silicone plug” method or using the

 included plastic cap.

PROPERTIES OF UNCURED MATERIAL

         Typical Value

Chemical Type                               Elastomeric Rubber

Appearance Metallic                                  Black

Specific Gravity @ 20°C                             1.31

   Viscosity                                              Thixotropic Past