太阳牌 RTV蓝色硅制垫片胶80022、 81860、 85860、 80628

Permatex Sensor-Safe Blue RTV Silicone Gasket

泰扬RTV蓝色硅制垫片胶


产品特点 使用领域 技术参数 使用方法 案例相关 使用视频 其他注意事项

Permatex泰扬蓝色垫片胶时一种防收缩、破裂、移位的现场成型垫片，具有低发挥性的特点。固化后形成粘结性高、弹性优越的胶体可密封垫圈，其填补缝隙大可达6mm,防止油滴及其他液体的渗漏。涂抹预切垫片胶提高了设备的可靠性，其间隙工作的适用温度范围在-54℃至260℃之间。


包装规格


型号

包装规格

每箱数量

产品代号

80022

3.盎司卡式管装

12

6BR

81860

7.5盎司自动胶管

6

6MA

85860

7.25盎司PowerBead罐装

1

85860

80628

13盎司卡桶

12

6C


Permatex Sensor Safe Blue RTV Silicone Gasket is a single

component, room temperature vulcanizing gasketing

compound designed to provide reliable “formed-in-place”

gaskets for mechanical assemblies. This material cures on

exposure to moisture in the air to form a tough, flexible,

silicone rubber gasket. The product resists aging, weathering

and thermal cycling without hardening, shrinking or cracking.

The original "Blue" gasketing product, refined and oxygen

sensor safe.


PRODUCT BENEFITS

● Superior adhesion and flexibility

● Sensor safe

● Replaces most cut gaskets

● Can be used as a gasket maker or dressing

● Easy application

● Non-flammable, Non-toxic


TYPICAL APPLICATIONS

Gasket maker for flexible flanges, Use as a sealant to coat

any precut gasket.


DIRECTIONS FOR USE

For assembly as a form-in-place gasket

  1. Remove all previous material from mating surfaces.

    Permatex Gasket Remover is recommend for most

    materials, not for plastics or painted surfaces.

  2. For bes results, clean and dry all surfaces with a re

    sidue-free solvent, such as Permatex Brake and

    Parts Cleaner.

  3. Cut nozzle to desired bead size,1/6 ti 1/4 in diame

    ter. A 1/8 bead is usually sufficient for most applic

    ations.

  4. Remove cap, puncture tube or cartridge seal and attach

    extension nozzle.

  5. Apply a continuous and even bead of silicone to one

    surface, first tracing the internal areas of the gasket

    configuration, then all surrounding bolt holes as shown

    below.

  6. Assemble parts immediately while silicone is still wet.

  7. Finger tighten flange only until material begins to seep

    out the sides of the flange.

  8. Allow to set for at least two hours and re-torque at lease

    one quarter to one half tum.

  9. For best results, allow to cure overnight.


For assembly as a gasket dressing

  1. Repeat steps 1 thru 4 as in previous section.

  2. Apply a thin film of silicone to one surface to be sealed.

  3. Place the pre cut gasket onto silicone film.

  4. Apply a second thin to pre-cut gasket surface.



5.Remove any excess and assemble parts immediately.

Note:Product not recommended for use as a cylinder

head gasket or head gasket sealant.


Instructions for PowerBead

  1. Clean and dry all flange surfaces to be sealed.

  2. Remove black cap from top of extension nozzle.

  3. Turn nozzle extension one complete turn(360)

    counterclockwise.

  4. Depress finger trigger and apply a continuous 1/16 inch

    to 1/8 inch PowerBead to one surface.

  5. Assemble parts immediately while silicone is still wet.

  6. Finger tighten flange only until material begins to seep

    out the sides of the flange.

  7. Allow to set for at least two hours and re-torque at least

    one quarter to one half turm.

  8. For best results, allow to cure overnight.

  9. To close ,turn extension nozzle clockwise until tight

  10. (about one full turn). Wipe off excess material from

    nozzle and replace black cap.



Storage of Unused Product

  1. Create a"Silicone Plug" by allowing excess material to

    extend beyond the extension nozzle or aerosol tip to

    cure, sealing and protecting the remaining product from

    moisture, For reuse, simply remove the cured product

    from the tip.

  2. For PowerBead dispensers, you may store remaining

    product using either the above "silicone plug" method or

    using the included plastic cap.


For Cleanup

  1. Remove uncured product from parts and hand-tools

    with Permatex Envirosafe ODC Free

    Cleaner/Degreaser. If skinned over, break film with a

    dry cloth to remove as much as possible. Remove the

    remaining material with Permatex Gasket Remover.

  2. Clean hands with a dry cloth or Permatex Fast 

    Orange hand cleaner.


PROPERTIES OF UNCURED MATERIAL

                                                       Typical Value

Chemical Type                       Acetoxy silicone rubber

Appearance                              Blue non-sag paste

Odor                                            Mild acetic acid

Specific Gravity                                       1.3

Extrusion rate@ 25℃（grams/min）      350

Flash Point ℃（℉  ）                             〉93（〉200）

 

TYPICAL CURING PERFORMANCE

Permatex Sensor Safe Blue RTV Silicone Gasket cures on

exposure to moisture in the air, The product dries tack free in

one hour and fully cures in 24 hours, Cure times will vary with

temperature, humidity and gap. Note: The curing process can

cause corrosion to some surfaces, for critical applications use

the UItra Series silicones.


PERFORMANCE OF CURED MATERIAL

After 7 days at 25℃（77℉  ），50% Relative Humidity

                                                           Typical Values

Hardness(Shore A),min                            32

Elongation,%,min.                                    350

Tensile Strength, N/mm2 （psi）,min       1.3 (190)

Gap Fill .inch                                            0.25

Material will stretch 3.5 times its original length before breaking.

Amount of force required to break material.


TYPICAL ENVIRONMENTAL RESISTANCE

Temperature Resistance                      Typical  Values

Continuous,℃（℉  ）                        -54 to 204   (-65 to 400)

Intermittent,℃（℉  ）                        -54 to 260(-65 to 500)


Chemical/ Solvent Resistance

The product retains effective properties in contact with

automotive fluids, such as motor oil, transmission fluids

alcohol and antifreeze solutions, Note:Not recommended for

parts in contact with gasoline.


GENERAL INFORMATION

This product is not recommended for use in pure oxygen

and/ or oxygen rich systems and should not be selected as

a sealant for chlorine or other strong oxidizing materials.


For  safe handling information on this product, consult the

Material Safety Data Sheet,(MSDS).


STORAGE

Products shall be ideally stored in a cool dry location in

unopened containers at a temperature between 8 to 28 ℃

（46 to 82 ℉  ）unless otherwise labeled, Optimal storage is at

the lower half of this temperature range, To prevent

contamination of unused product, do not return any material to its original container


NOTE

The data contained herein are furnished for information only

and are believed to reliable. We cannot assume

responsibility for the results obtained by others over whose

methods we have no control. Permatex Inc. specifically

disclaims all warranties expressed or implied,including

warranties of merchantability or fitness for a particular 

products and disclaims any liability for consequential or 

incidental damages of any kind ,including lost profits.

This product may be covered by one or more United States or

foreign patents or patent applications


●避免与皮肤及眼睛直接接触，请于使用时戴上塑胶手套及安全护目镜。

●若因接触皮肤引起过敏及红斑，请以肥皂及清水沖洗；若不慎触碰到眼睛时，请立即以清水沖洗并就医诊查

●勿吞食、勿让孩童取用。

●使用本材料的工作环境须通风良好，勿在密闭空间使用。